Mount your BbTalkin 3.0 intercoms and headsets securely for the best performance on water, snow, or land.
This guide shows you how to attach each mount type - including helmet pads, rubber mounts, slide mounts, and strap mounts - for helmets, hats, and sports headsets.
Follow these step-by-step instructions to ensure a firm fit, clear audio, and full IPX7 waterproof protection every session.
How to mount the B02R or B03R helmet pads to your helmet
Clean surface:
Use an alcohol pad to clean the surface thoroughly.
Note: Scratched surfaces or old, worn helmets may affect the mount’s durability.
Placing helmet pad Velcro:
Place the S08 Velcro tape just above the ear. Use the earpad as a reference to determine the correct placement for the Velcro.
We recommend allowing the adhesive to set overnight for best results.
For the B03, repeat the same process on the other side.
Loop the chin buckle:
When installing the B02R or B03R earpads, make sure to loop the chin buckle through the elastic band to secure the headset. This helps keep the earpads firmly in place near the ears and prevents them from coming loose during strong impacts.
How to mount rubber mount S06R to your helmet
Clean surface:
Use an alcohol pad to clean the surface thoroughly.
Note: Scratched surfaces or old, worn helmets may affect the mount’s durability.
Take out the vent that covers the earhole.
Place helmet pad:
Place the B02G helmet pad for GATH directly over the earhole, ensuring the microphone is facing forward.
Allow it to dry overnight for best results.
Position intercom:
Make sure to position the mount with the intercom as close as possible to the earpad to ensure the headset’s audio cable has enough room to reach the intercom.
Allow it to dry overnight for best results.
How to Mount the Rubber Mount S06R to Your Helmet
Clean surface:
Use an alcohol pad to clean the surface thoroughly.
Note: Scratched surfaces or old, worn helmets may affect the mount’s durability.
Attach intercom to rubber mount:
Place the intercom into the S06R rubber mount, then stretch the rubber band over the unit and secure it behind the pins so it’s held firmly.
Peel off one side of the adhesive, stick it to the back of the mount, and press firmly.
Position intercom:
Make sure to position the mount with the intercom as close as possible to the earpad to ensure the headset’s audio cable has enough room to reach the intercom.
Remove the remaining backing and press firmly to fix it in place.
Allow it to dry overnight for best results.
How to mount slide mount S06 to your helmet
Clean surface:
Use an alcohol pad to clean the surface thoroughly.
Note: Scratched surfaces or old, worn helmets may affect the mount’s durability.
Attach intercom to rubber mount:
Place the intercom into the S06R rubber mount, then stretch the rubber band over the unit and secure it behind the pins so it’s held firmly.
Peel off one side of the adhesive, stick it to the back of the mount, and press firmly.
Position intercom:
Make sure to position the mount with the intercom as close as possible to the earpad to ensure the headset’s audio cable has enough room to reach the intercom.
Remove the remaining backing and press firmly to fix it in place.
Allow it to dry overnight for best results.
How to mount S04 to clip mount to any fabric
How to use clip mount:
The S04 clip mount can be attached underneath the rim of the helmet or onto any other fabric surface.
To install it, slide the clip in from underneath with the back side facing the fabric, ensuring it fits securely in place.
Attach intercom to clip mount:
Place the intercom into the S06 slide mount and press the intercom into the specially designed holes and press down firmly to secure it.
Ensure that both back clips are aligned straight, and avoid using excessive force during installation.
Position intercom onto fabric:
Make sure to position the mount with the intercom as close as possible to the edge upward to ensure it stays firmly in place.
Note: the headset’s audio cable needs enough room to reach the intercom.
How to mount intercom to HAT, CAP or SPORTSET
How to use strap mount:
Use the special mount designed for straps, ensuring that all four pins are positioned behind the elastic band or fabric for a secure fit.
The Hat (B01HR) and Cap (B01CR) feature extra fabric on the left side of the head to accommodate the mount, while the Sports Headset (B01R) includes a separate S05 armband that allows the mount and intercom to be attached to the arm.
Attach intercom to strap mount:
Place the intercom into the mount and press the intercom into the specially designed holes and press down firmly to secure it.
Ensure that both back clips are aligned straight, and avoid using excessive force during installation.
Position intercom onto Headsets:
The end result should ook like this. The intercom antenna pointing upward. And the Advance attached to the left side of the user.
Mounting Tips
- Always clean and dry mounting surfaces before installation.
- Let adhesives cure for 12–24 hours at room temperature.
- Avoid textured or uneven surfaces unless using S06R rubber mounts.
- Keep the antenna pointing upward for the best Bluetooth range.
- Rinse and dry mounts after saltwater use to extend adhesive life.
- Recheck mounts before every session to ensure secure fit.
Need Help?
If you’re unsure which mount is best for your helmet, headset, or sport setup, contact our team for advice.
We can help you choose the correct mounting kit for your gear.
Email:sales@bb-talkin.nl
Frequently Asked Questions About BbTalkin 3.0 Mounting & Setup
Which mount works best for my helmet?
Use S06R for curved helmets, S06 for flat surfaces, and S04 for flexible materials like wetsuit hoods or caps.
How long should I let the adhesive cure before use?
Allow adhesive pads to cure overnight (12–24 hours) before attaching your intercom.
Can I reuse a mount after removing it?
No - always replace adhesive pads or mounts after removal for maximum waterproof sealing and grip.
How do I clean mounts after saltwater exposure?
Rinse with fresh water, dry thoroughly, and avoid direct sunlight during storage.
Do I need to pair my BbTalkin devices every time I use them?
No. Once your BbTalkin 3.0 intercoms are paired, they automatically reconnect when powered on. If you reset or change devices, simply re-pair using the same steps.
What’s the safest way to remove an old mount?
Warm the adhesive gently with a hairdryer, then peel slowly from the edges without using sharp tools.
