Mount your BbTalkin 3.0 intercoms and headsets securely for the best performance on water, snow, or land.
This guide shows you how to attach each mount type - including helmet pads, rubber mounts, slide mounts, and strap mounts - for helmets, hats, and sports headsets.
Follow these step-by-step instructions to ensure a firm fit, clear audio, and full IPX7 waterproof protection every session.
How to mount the B02R or B03R helmet pads to your helmet
Clean surface:
Use an alcohol pad to clean the surface thoroughly.
Note: Scratched surfaces or old, worn helmets may affect the mount’s durability.
Placing helmet pad Velcro:
Place the S08 Velcro tape just above the ear. Use the earpad as a reference to determine the correct placement for the Velcro.
We recommend allowing the adhesive to set overnight for best results.
For the B03, repeat the same process on the other side.
Loop the chin buckle:
When installing the B02R or B03R earpads, make sure to loop the chin buckle through the elastic band to secure the headset. This helps keep the earpads firmly in place near the ears and prevents them from coming loose during strong impacts.
Comment installer le coussinet de casque B02G (pour casques GATH)
Clean surface:
Use an alcohol pad to clean the surface thoroughly.
Note: Scratched surfaces or old, worn helmets may affect the mount’s durability.
Take out the vent that covers the earhole.
Place helmet pad:
Place the B02G helmet pad for GATH directly over the earhole, ensuring the microphone is facing forward.
Allow it to dry overnight for best results.
Position intercom:
Make sure to position the mount with the intercom as close as possible to the earpad to ensure the headset’s audio cable has enough room to reach the intercom.
Allow it to dry overnight for best results.
Comment installer le support en caoutchouc S06R
Clean surface:
Use an alcohol pad to clean the surface thoroughly.
Note: Scratched surfaces or old, worn helmets may affect the mount’s durability.
Attach intercom to rubber mount:
Place the intercom into the S06R rubber mount, then stretch the rubber band over the unit and secure it behind the pins so it’s held firmly.
Peel off one side of the adhesive, stick it to the back of the mount, and press firmly.
Position intercom:
Make sure to position the mount with the intercom as close as possible to the earpad to ensure the headset’s audio cable has enough room to reach the intercom.
Remove the remaining backing and press firmly to fix it in place.
Allow it to dry overnight for best results.
Comment installer le support à clip S04 (sur tout tissu ou jante)
Clean surface:
Use an alcohol pad to clean the surface thoroughly.
Note: Scratched surfaces or old, worn helmets may affect the mount’s durability.
Attach intercom to rubber mount:
Place the intercom into the S06R rubber mount, then stretch the rubber band over the unit and secure it behind the pins so it’s held firmly.
Peel off one side of the adhesive, stick it to the back of the mount, and press firmly.
Position intercom:
Make sure to position the mount with the intercom as close as possible to the earpad to ensure the headset’s audio cable has enough room to reach the intercom.
Remove the remaining backing and press firmly to fix it in place.
Allow it to dry overnight for best results.
Comment fixer l'interphone sur un chapeau, une casquette ou un casque de sport
How to use clip mount:
The S04 clip mount can be attached underneath the rim of the helmet or onto any other fabric surface.
To install it, slide the clip in from underneath with the back side facing the fabric, ensuring it fits securely in place.
Attach intercom to clip mount:
Place the intercom into the S06 slide mount and press the intercom into the specially designed holes and press down firmly to secure it.
Ensure that both back clips are aligned straight, and avoid using excessive force during installation.
Position intercom onto fabric:
Make sure to position the mount with the intercom as close as possible to the edge upward to ensure it stays firmly in place.
Note: the headset’s audio cable needs enough room to reach the intercom.
How to mount intercom to HAT, CAP or SPORTSET
How to use strap mount:
Use the special mount designed for straps, ensuring that all four pins are positioned behind the elastic band or fabric for a secure fit.
The Hat (B01HR) and Cap (B01CR) feature extra fabric on the left side of the head to accommodate the mount, while the Sports Headset (B01R) includes a separate S05 armband that allows the mount and intercom to be attached to the arm.
Attach intercom to strap mount:
Place the intercom into the mount and press the intercom into the specially designed holes and press down firmly to secure it.
Ensure that both back clips are aligned straight, and avoid using excessive force during installation.
Position intercom onto Headsets:
The end result should ook like this. The intercom antenna pointing upward. And the Advance attached to the left side of the user.
Conseils de montage
- Toujours nettoyer et sécher les surfaces de montage avant l'installation.
- Laisser les adhésifs sécher pendant 12 à 24 heures à température ambiante.
- Évitez les surfaces texturées ou irrégulières, sauf si vous utilisez des supports en caoutchouc S06R .
- Pour une portée Bluetooth optimale, orientez l'antenne vers le haut.
- Rincez et séchez les supports après utilisation en eau salée pour prolonger la durée de vie de l'adhésif.
- Revérifiez les fixations avant chaque séance pour garantir un maintien sûr.
Besoin d'aide?
Si vous n'êtes pas certain du support le mieux adapté à votre casque, vos écouteurs ou votre équipement sportif, contactez notre équipe pour obtenir des conseils.
Nous pouvons vous aider à choisir le kit de montage adapté à votre équipement.
Adresse électronique : sales@bb-talkin.nl
Questions fréquemment posées
Quel support convient le mieux à mon casque ?
Utilisez S06R pour les casques incurvés, S06 pour les surfaces planes et S04 pour les matériaux flexibles comme les cagoules ou les bonnets de combinaisons de plongée.
Combien de temps dois-je laisser sécher l'adhésif avant utilisation ?
Laissez les pastilles adhésives sécher pendant la nuit (12 à 24 heures) avant de fixer votre interphone.
Puis-je réutiliser un support après l'avoir retiré ?
Non – il faut toujours remettre en place les pastilles adhésives ou les supports après leur retrait pour une étanchéité et une adhérence maximales.
Comment nettoyer les supports après une exposition à l'eau salée ?
Rincer à l'eau claire, sécher soigneusement et éviter l'exposition directe au soleil pendant le stockage.
Dois-je appairer mes appareils BbTalkin à chaque fois que je les utilise ?
Non. Une fois vos interphones BbTalkin 3.0 appairés, ils se reconnectent automatiquement à la mise sous tension. Si vous réinitialisez ou changez d'appareil, il vous suffit de les appairer à nouveau en suivant les mêmes étapes.
Quelle est la méthode la plus sûre pour retirer un ancien support ?
Chauffez légèrement l'adhésif à l'aide d'un sèche-cheveux, puis décollez-le lentement en partant des bords sans utiliser d'outils pointus.
